MaretronRaymarine
Do Maretron and Raymarine work together?
Yes, mostly one way. We compared 6 Maretron–Raymarine model pairs using only the data lists (PGNs) the makers publish. 2 have data flowing both ways, 4 one way only. Maretron to Raymarine: mainly route & waypoint navigation, boat speed & log, depth and temperature & weather. Raymarine to Maretron: mainly position & time, heading & motion, boat speed & log and depth. Maker-specific (proprietary) messages, used for things like cross-brand autopilot control or sonar sharing, are not counted between different brands.
Boat electronics share data over NMEA 2000 using numbered messages called PGNs (Parameter Group Numbers). Data only “flows” here when one maker's manual says its device sends a message and the other maker's manual says its device receives the same message.
These are compatible:
- Maretron DSM250 + Raymarine Axiom (LightHouse 4)Share position & time, heading & motion, boat speed & log and 4 more (one way, Raymarine Axiom (LightHouse 4) → Maretron DSM250).
- Maretron USB100 + Raymarine Axiom (LightHouse 4)Share position & time, heading & motion, boat speed & log and 4 more (both ways).
- Maretron DSM250 + Raymarine i70sShare position & time, heading & motion, boat speed & log and 5 more (one way, Raymarine i70s → Maretron DSM250).
- Maretron USB100 + Raymarine i70sShare position & time, heading & motion, boat speed & log and 5 more (both ways).
- Maretron DST110 + Raymarine i70Share boat speed & log, depth and temperature & weather (one way, Maretron DST110 → Raymarine i70).
- Maretron GPS200 + Raymarine i70Share position & time, heading & motion and boat speed & log (one way, Maretron GPS200 → Raymarine i70).
“Compatible” here means they connect over NMEA 2000 and share data according to the makers' published lists. Maker-specific messages (e.g. cross-brand autopilot control) are not counted.
Model by model
Data types each way, from the makers' published lists. Tap a pair to open it in the checker.
Maretron USB100 + Raymarine i70s Shares data both ways
Gateway / converter + Instrument display · Check this pair
| Data type | Maretron USB100 → Raymarine i70s | Raymarine i70s → Maretron USB100 |
|---|---|---|
| Position & time | — | Flows 4 messages: Position, Rapid Update (129025); COG & SOG, Rapid Update (129026); GNSS Position Data (129029); +1 more |
| Heading & motion | — | Flows 2 messages: Vessel Heading (127250); Rate of Turn (127251) |
| Boat speed & log | — | Flows 2 messages: Speed (128259); Distance Log (128275) |
| Depth | — | Flows 1 message: Water Depth (128267) |
| Wind | — | Flows 1 message: Wind Data (130306) |
| Temperature & weather | — | Flows 2 messages: Environmental Parameters (obsolete) (130310); Environmental Parameters (130311) |
| Route & waypoint navigation | Flows 2 messages: Cross Track Error (129283); Navigation Data (129284) | — |
| Autopilot & steering | — | Flows 1 message: Rudder (127245) |
Maretron USB100 + Raymarine Axiom (LightHouse 4) Shares data both ways
Gateway / converter + Chartplotter / MFD · Check this pair
| Data type | Maretron USB100 → Raymarine Axiom (LightHouse 4) | Raymarine Axiom (LightHouse 4) → Maretron USB100 |
|---|---|---|
| Position & time | — | Flows 6 messages: Position, Rapid Update (129025); COG & SOG, Rapid Update (129026); GNSS Position Data (129029); +3 more |
| Heading & motion | — | Flows 3 messages: Vessel Heading (127250); Rate of Turn (127251); Attitude (127257) |
| Boat speed & log | — | Flows 2 messages: Speed (128259); Distance Log (128275) |
| Depth | — | Flows 1 message: Water Depth (128267) |
| Wind | — | Flows 1 message: Wind Data (130306) |
| Temperature & weather | — | Flows 1 message: Environmental Parameters (obsolete) (130310) |
| Route & waypoint navigation | Flows 2 messages: Cross Track Error (129283); Navigation Data (129284) | — |
Maretron DSM250 + Raymarine i70s One way only
Instrument display + Instrument display · Check this pair
| Data type | Maretron DSM250 → Raymarine i70s | Raymarine i70s → Maretron DSM250 |
|---|---|---|
| Position & time | — | Flows 4 messages: Position, Rapid Update (129025); COG & SOG, Rapid Update (129026); GNSS Position Data (129029); +1 more |
| Heading & motion | — | Flows 3 messages: Vessel Heading (127250); Rate of Turn (127251); Magnetic Variation (127258) |
| Boat speed & log | — | Flows 2 messages: Speed (128259); Distance Log (128275) |
| Depth | — | Flows 1 message: Water Depth (128267) |
| Wind | — | Flows 1 message: Wind Data (130306) |
| Temperature & weather | — | Flows 2 messages: Environmental Parameters (obsolete) (130310); Environmental Parameters (130311) |
| Route & waypoint navigation | — | Flows 2 messages: Cross Track Error (129283); Navigation Data (129284) |
| Autopilot & steering | — | Flows 1 message: Rudder (127245) |
Maretron DSM250 + Raymarine Axiom (LightHouse 4) One way only
Instrument display + Chartplotter / MFD · Check this pair
| Data type | Maretron DSM250 → Raymarine Axiom (LightHouse 4) | Raymarine Axiom (LightHouse 4) → Maretron DSM250 |
|---|---|---|
| Position & time | — | Flows 6 messages: Position, Rapid Update (129025); COG & SOG, Rapid Update (129026); GNSS Position Data (129029); +3 more |
| Heading & motion | — | Flows 4 messages: Vessel Heading (127250); Rate of Turn (127251); Attitude (127257); +1 more |
| Boat speed & log | — | Flows 2 messages: Speed (128259); Distance Log (128275) |
| Depth | — | Flows 1 message: Water Depth (128267) |
| Wind | — | Flows 1 message: Wind Data (130306) |
| Temperature & weather | — | Flows 1 message: Environmental Parameters (obsolete) (130310) |
| Route & waypoint navigation | — | Flows 4 messages: Cross Track Error (129283); Navigation Data (129284); Navigation - Route/WP Information (129285); +1 more |
Maretron DST110 + Raymarine i70 One way only
Depth / speed sensor + Instrument display · Check this pair
| Data type | Maretron DST110 → Raymarine i70 | Raymarine i70 → Maretron DST110 |
|---|---|---|
| Boat speed & log | Flows 2 messages: Speed (128259); Distance Log (128275) | — |
| Depth | Flows 1 message: Water Depth (128267) | — |
| Temperature & weather | Flows 3 messages: Environmental Parameters (obsolete) (130310); Environmental Parameters (130311); Temperature (130312) | — |
Maretron GPS200 + Raymarine i70 One way only
GPS / heading sensor + Instrument display · Check this pair
| Data type | Maretron GPS200 → Raymarine i70 | Raymarine i70 → Maretron GPS200 |
|---|---|---|
| Position & time | Flows 3 messages: Position, Rapid Update (129025); COG & SOG, Rapid Update (129026); GNSS Position Data (129029) | — |
| Heading & motion | Flows 1 message: Magnetic Variation (127258) | — |
| Boat speed & log | Flows 1 message: Speed (128259) | — |
Gaps and fixes
Data that both devices in a pair handle, but that one can use and the other doesn't send (or sends as a different message number). Fixes only name devices whose published list sends that data.
- Autopilot & steering: Maretron DSM250, Raymarine Axiom (LightHouse 4) and Maretron USB100 can use it, but the paired device doesn't send it. Could come from: Simrad NAC-2; Raymarine EV-1; Actisense NGW-1 (converts from an existing NMEA 0183 device).Simrad NAC-2 autopilot computerSends autopilot & steering (its maker's list says so).
- Engine & propulsion: Maretron DSM250, Raymarine Axiom (LightHouse 4), Maretron USB100 and Raymarine i70s can use it, but the paired device doesn't send it. Could come from: Maretron J2K100; Yacht Devices YDEG-04; Yacht Devices YDWG-02 (converts from an existing NMEA 0183 device).Maretron J2K100 J1939 to NMEA 2000 gatewaySends engine & propulsion (its maker's list says so).
- Batteries & DC power: Maretron DSM250, Raymarine Axiom (LightHouse 4), Maretron USB100 and Raymarine i70s can use it, but the paired device doesn't send it. Could come from: Xantrex Freedom X/XC; Victron VE.Bus inverter/charger; Yacht Devices YDWG-02 (converts from an existing NMEA 0183 device); Maretron DCM100.Xantrex Freedom X/XCSends batteries & DC power (its maker's list says so).No official product page checked yet. Ask your dealer.
- Tank levels: Maretron DSM250, Raymarine Axiom (LightHouse 4), Maretron USB100 and Raymarine i70s can use it, but the paired device doesn't send it. Could come from: Maretron TLA100; Yacht Devices YDEG-04; Yacht Devices YDWG-02 (converts from an existing NMEA 0183 device).Maretron TLA100 tank level adapterSends tank levels (its maker's list says so).
Check with the manufacturer before buying. Buttons open the maker's own product page unless marked as an affiliate link.
Also in the checker: Maretron J2K100, Maretron TLA100, Maretron SSC300, Maretron DCM100, Maretron FPM100, Maretron ACM100, Maretron WSO100, Raymarine EV-1, Raymarine AIS700, Raymarine Ray53/Ray63, Raymarine Ray73, Raymarine Evolution ACU.
Installing these together
Both connect to one NMEA 2000 backbone. Full basics, with sources, are in the NMEA 2000 install guide.
What you need
- A backbone with one T-connector per device, plus one for the power cable. (Garmin support)
- Drop cables of 6 m (20 ft) or less from each T to its device. (Garmin N2K reference, B&G Zeus S manual)
- Exactly two terminators, one at each end. Don't add more if the boat's backbone already has them. (Garmin N2K reference)
- One fused 12 V power tap, switched so it doesn't drain the battery. (Garmin N2K reference, B&G Zeus S manual, Raymarine docs)
- Raymarine: Raymarine uses SeaTalk NG (its own connectors on the NMEA 2000 bus). To mix with standard NMEA 2000 (DeviceNet) cabling, use SeaTalk NG ↔ DeviceNet adaptors such as A06082, A06083 or A06084 (spur) or A80674/A80675 (backbone). (Raymarine, Raymarine docs)
- Raymarine: Power SeaTalk NG from one 12 V supply with a 5 A inline fuse, ideally at the middle (balanced). Don't use the engine-start battery. (Raymarine docs, Raymarine 81300)
Set-up on the display
- Raymarine: Choose preferred sources under Homescreen > Settings > Data sources (depth, speed, heading, GNSS, wind and more). (Raymarine LightHouse 4)
- Raymarine: Raymarine devices on the network are updated from a LightHouse display that is the Data master. (Raymarine docs)
- Maretron: we haven't collected a maker set-up page yet. Follow the device's own manual.
- Update each device's software. Garmin says an update may be needed when you add a device or accessory. (Garmin manual, Raymarine docs)
How long? Estimate
No maker publishes a DIY time. Our rough estimate: 1.5–3 hours to add one device to an existing, healthy backbone, or 4–7 hours to build a new small backbone for 2–4 devices.
How we got it: plan the backbone and measure (Garmin says to start with a diagram), run one drop cable, fit Ts, terminators and the power tap, update software, then select sources and test, plus SeaTalk NG adaptor. It doesn't include mounting displays or transducers, cutting holes or long cable runs through the boat. If in doubt, use a qualified (NMEA-certified) installer. (Garmin N2K reference)
Common problems
Only from makers' manuals, support articles and installation guides.
- Wrong number of terminators. There must be exactly two 120 Ω terminators, one at each end of the backbone. With the network power off, CAN-H to CAN-L should read about 60 Ω. 120 Ω means one is missing; 40 Ω means there's one too many. (Garmin support, Actisense)
- Low network voltage. Devices need at least 9 V at the far end of the backbone (Navico says errors can start below 9.5 V). On long or busy backbones, move the power tap towards the middle. (Actisense, Simrad NSS 4 manual, Garmin N2K reference)
- Duplicate data sources. Two GPS units or two depth sensors on one network can conflict. Pick the preferred source on the display. Raymarine says to have only one source per data type unless a product's documents allow more. (Raymarine 81300, Raymarine LightHouse 4, B&G NEON notes)
- Maker-only features don't cross brands. Standard data flows, but a Garmin plotter can't engage or control a third-party autopilot: it only sends Go To / Route To navigation data. Raymarine Evolution pilots list only Raymarine controllers and displays as control heads. (Garmin support, Raymarine 87472)
More checks (power feeds, devices not showing up): install guide. Check with the manufacturer or a qualified installer before buying or drilling.
What you'll need to connect this
Example: a Maretron DSM250 and a Raymarine Axiom (LightHouse 4) on a new backbone.
For 2 devices on one NMEA 2000 backbone. From the makers' install guides; see the install guide for sources. Quantities are estimates
- 1 runBackbone cableLong enough to pass every device; the length depends on your boat. Plan it on a sketch first.
- 3est.T-connectorsOne per device, plus one for the power cable.
- 2est.Drop cablesOne per device, 6 m (20 ft) or less each. Many devices come with a T-connector and drop cable in the box (Garmin lists them for the GPS 24xd, AIS 800 and GND 10), so check before you buy.
- 2TerminatorsExactly two, one at each end. Skip them if your backbone already has two.
- 1Power cable (power tap)One fused 12 V feed, in one place only, switched so it doesn't drain the battery.
One kit covers the basics
Brand adapters for your devices
Check with the manufacturer before buying. Buttons open the maker's own product page unless marked as an affiliate link.
Open these devices in the checker to add the rest of your boat and get a kit list for all of it.
Frequently asked
Are Maretron and Raymarine compatible?
Yes, mostly one way. We compared 6 Maretron–Raymarine model pairs using only the data lists (PGNs) the makers publish. 2 have data flowing both ways, 4 one way only. Maretron to Raymarine: mainly route & waypoint navigation, boat speed & log, depth and temperature & weather. Raymarine to Maretron: mainly position & time, heading & motion, boat speed & log and depth. Maker-specific (proprietary) messages, used for things like cross-brand autopilot control or sonar sharing, are not counted between different brands. Check with the manufacturer before buying.
What data can a Maretron DSM250 and a Raymarine Axiom (LightHouse 4) share?
Nothing confirmed from the Maretron DSM250 to the Raymarine Axiom (LightHouse 4). From the Raymarine Axiom (LightHouse 4) to the Maretron DSM250: position & time, heading & motion, boat speed & log, depth, wind, temperature & weather and route & waypoint navigation. Based on the makers' published PGN lists.
What doesn't work between Maretron and Raymarine?
Some pairs also have data that one device can use but neither sends, such as autopilot & steering, engine & propulsion, batteries & DC power and tank levels; that needs another device or a gateway. The fixes on this page only name devices whose published list sends that data.
Sources
- Maretron DSM250 (Maretron DSM250 multi-function display): DSM250 User's Manual, Revision 1.6.2. manufacturer. Last checked 2026-11-19. Confidence: high; list complete.
- Raymarine Axiom (LightHouse 4) (Raymarine Axiom / Axiom+ / Axiom Pro / Axiom 2 Pro / Axiom XL (LightHouse 4)): Axiom LightHouse 4 Operation Instructions (81406) – NMEA 2000 PGN support, 81406 Rev 30. manufacturer. Last checked 2026-11-19. Confidence: high; list complete.
- Maretron USB100 (Maretron USB100 NMEA 2000 to USB gateway (NMEA 0183 output)): USB100 User's Manual, Revision 1.8. manufacturer. Last checked 2026-11-19. Confidence: high; list complete.
- Raymarine i70s (Raymarine i70s multifunction instrument display): i70s Installation Instructions (87420), 87420 Rev 2, 10-2025. manufacturer. Last checked 2026-11-19. Confidence: high; list complete.
- Maretron DST110 (Maretron DST110 depth/speed/temperature transducer): DST110 User's Manual, Revision 1.3. manufacturer. Last checked 2026-11-19. Confidence: high; list complete.
- Raymarine i70 (Raymarine i70 multifunction instrument display): i70 Installation Instructions (87425), 87425 Rev 2. manufacturer. Last checked 2026-11-19. Confidence: high; list complete.
- Maretron GPS200 (Maretron GPS200 GPS antenna/receiver): GPS200 User's Manual, Revision 1.4. manufacturer. Last checked 2026-11-19. Confidence: high; list complete.
Installation sources
- Garmin Support: NMEA 2000 Troubleshooting on Garmin Marine Devices. Checked 2026-11-19.
- Garmin: Technical Reference for Garmin NMEA 2000 Products. Checked 2026-11-19.
- Navico Group (B&G): B&G Zeus S Installation Manual 988-12624-001 – NMEA 2000 planning. Checked 2026-11-19.
- Raymarine: SeaTalk NG cables and accessories. Checked 2026-11-19.
- Raymarine: SeaTalk NG to NMEA 2000 Adaptors. Checked 2026-11-19.
- Raymarine: SeaTalk NG Reference Manual 81300 (dealer-hosted copy). Checked 2026-11-19.
- Raymarine: SeaTalk NG system loading. Checked 2026-11-19.
- Raymarine: LightHouse 4 – Data sources settings menu. Checked 2026-11-19.
- Raymarine: Software updates (product installation instructions). Checked 2026-11-19.
- Garmin: GPSMAP x3 Owner's Manual – Software Updates. Checked 2026-11-19.
- Actisense: How to build & troubleshoot an NMEA 2000 network. Checked 2026-11-19.
- Navico Group (Simrad): Simrad NSS 4 Installation Manual – NMEA 2000 planning (distributor-hosted copy). Checked 2026-11-19.
- Garmin: Technical Reference for Garmin NMEA 2000 Products – Power Distribution and Balance. Checked 2026-11-19.
- Navico Group (B&G): NEON 2.5 software release notes (B&G Zeus S / SR). Checked 2026-11-19.
- Garmin Support: Using Third-Party Marine Autopilots with a Garmin Chartplotter. Checked 2026-11-19.
- Raymarine: Evolution EV-1 Autopilot Installation Instructions 87472 Rev 2 (12-2025), ch. 3–4. Checked 2026-11-19.
How we pick pages: chosen by hand from common brand combinations, not from search data. Model pairs are picked automatically from the devices in our dataset (main chartplotter of each brand plus devices that exchange data with it).
Other brand pairs
Garmin + Raymarine · Raymarine + Simrad · Lowrance + Raymarine · B&G + Raymarine · Raymarine + Victron · Yacht Devices + Raymarine · Maretron + Garmin · All brand pairs