VictronGarmin
Do Victron and Garmin work together?
Yes, mostly one way. We compared 6 Victron–Garmin model pairs using only the data lists (PGNs) the makers publish. 1 has data flowing both ways, 5 one way only. Victron to Garmin: mainly batteries & DC power, tank levels, AC power & generator and switching, lighting & trim. Garmin to Victron: mainly position & time, batteries & DC power and tank levels. Less certain for Victron Cerbo GX, Victron Skylla-i, Victron BlueSolar MPPT 150/70 and Victron BMV-700, because of caveats in their published list (partial list, no send/receive direction, or an older, range-wide or dealer-hosted document). Maker-specific (proprietary) messages, used for things like cross-brand autopilot control or sonar sharing, are not counted between different brands.
Boat electronics share data over NMEA 2000 using numbered messages called PGNs (Parameter Group Numbers). Data only “flows” here when one maker's manual says its device sends a message and the other maker's manual says its device receives the same message.
These are compatible:
No model pair on this page is confirmed by two full published lists.
“Compatible” here means they connect over NMEA 2000 and share data according to the makers' published lists. Maker-specific messages (e.g. cross-brand autopilot control) are not counted.
Needs checking:
- Victron Cerbo GX + Garmin GPSMAP x3 (7x3–16x3)Manuals confirm position & time, batteries & DC power and tank levels (both ways), but Victron Cerbo GX doesn't publish a full list.
- Victron Skylla-i + Garmin GPSMAP x3 (7x3–16x3)Manuals confirm batteries & DC power, AC power & generator and switching, lighting & trim (one way, Victron Skylla-i → Garmin GPSMAP x3 (7x3–16x3)), but Victron Skylla-i doesn't publish a full list.
- Victron BlueSolar MPPT 150/70 + Garmin GNX 20/21Manuals confirm batteries & DC power (one way, Victron BlueSolar MPPT 150/70 → Garmin GNX 20/21), but Victron BlueSolar MPPT 150/70 doesn't publish a full list.
- Victron BlueSolar MPPT 150/70 + Garmin GMI 20Manuals confirm batteries & DC power (one way, Victron BlueSolar MPPT 150/70 → Garmin GMI 20), but Victron BlueSolar MPPT 150/70 doesn't publish a full list.
- Victron BMV-700 + Garmin GNX 20/21Manuals confirm batteries & DC power (one way, Victron BMV-700 → Garmin GNX 20/21), but Victron BMV-700 doesn't publish a full list.
- Victron BMV-700 + Garmin GMI 20Manuals confirm batteries & DC power (one way, Victron BMV-700 → Garmin GMI 20), but Victron BMV-700 doesn't publish a full list.
Model by model
Data types each way, from the makers' published lists. Tap a pair to open it in the checker.
Victron Cerbo GX + Garmin GPSMAP x3 (7x3–16x3) Shares data both ways
Gateway / converter + Chartplotter / MFD · Check this pair
| Data type | Victron Cerbo GX → Garmin GPSMAP x3 (7x3–16x3) | Garmin GPSMAP x3 (7x3–16x3) → Victron Cerbo GX |
|---|---|---|
| Position & time | — | Flows 3 messages: Position, Rapid Update (129025); COG & SOG, Rapid Update (129026); GNSS Position Data (129029) |
| Engine & propulsion | — | Different message : both handle this data but list different PGNs |
| Batteries & DC power | Flows 4 messages: DC Detailed Status (127506); Charger Status (127507); Battery Status (127508); +1 more | Flows 1 message: Battery Status (127508) |
| Tank levels | Flows 1 message: Fluid Level (127505) | Flows 1 message: Fluid Level (127505) |
Check before buying. Victron Cerbo GX: Only part of its data-message (PGN) list is published. Medium confidence: older or range-wide document. Its list Tell us if it worked
Victron Skylla-i + Garmin GPSMAP x3 (7x3–16x3) One way only
Battery charger + Chartplotter / MFD · Check this pair
| Data type | Victron Skylla-i → Garmin GPSMAP x3 (7x3–16x3) | Garmin GPSMAP x3 (7x3–16x3) → Victron Skylla-i |
|---|---|---|
| Batteries & DC power | Flows 2 messages: Charger Status (127507); Battery Status (127508) | — |
| AC power & generator | Flows 1 message: AC Input Status (127503) | — |
| Switching, lighting & trim | Flows 1 message: Binary Switch Bank Status (127501) | — |
Check before buying. Victron Skylla-i: Only part of its data-message (PGN) list is published. No receive list is published, so we can't tell what data it accepts. Medium confidence: older or range-wide document. Its list Tell us if it worked
Victron BlueSolar MPPT 150/70 + Garmin GNX 20/21 One way only
Solar charger + Instrument display · Check this pair
| Data type | Victron BlueSolar MPPT 150/70 → Garmin GNX 20/21 | Garmin GNX 20/21 → Victron BlueSolar MPPT 150/70 |
|---|---|---|
| Batteries & DC power | Flows 1 message: Battery Status (127508) | — |
Check before buying. Victron BlueSolar MPPT 150/70: Only part of its data-message (PGN) list is published. No receive list is published, so we can't tell what data it accepts. Medium confidence: older or range-wide document. Its list Tell us if it worked
Victron BlueSolar MPPT 150/70 + Garmin GMI 20 One way only
Solar charger + Instrument display · Check this pair
| Data type | Victron BlueSolar MPPT 150/70 → Garmin GMI 20 | Garmin GMI 20 → Victron BlueSolar MPPT 150/70 |
|---|---|---|
| Batteries & DC power | Flows 1 message: Battery Status (127508) | — |
Check before buying. Victron BlueSolar MPPT 150/70: Only part of its data-message (PGN) list is published. No receive list is published, so we can't tell what data it accepts. Medium confidence: older or range-wide document. Its list Tell us if it worked
Victron BMV-700 + Garmin GNX 20/21 One way only
Battery monitor + Instrument display · Check this pair
| Data type | Victron BMV-700 → Garmin GNX 20/21 | Garmin GNX 20/21 → Victron BMV-700 |
|---|---|---|
| Batteries & DC power | Flows 1 message: Battery Status (127508) | — |
Check before buying. Victron BMV-700: Only part of its data-message (PGN) list is published. No receive list is published, so we can't tell what data it accepts. Medium confidence: older or range-wide document. Its list Tell us if it worked
Victron BMV-700 + Garmin GMI 20 One way only
Battery monitor + Instrument display · Check this pair
| Data type | Victron BMV-700 → Garmin GMI 20 | Garmin GMI 20 → Victron BMV-700 |
|---|---|---|
| Batteries & DC power | Flows 1 message: Battery Status (127508) | — |
Check before buying. Victron BMV-700: Only part of its data-message (PGN) list is published. No receive list is published, so we can't tell what data it accepts. Medium confidence: older or range-wide document. Its list Tell us if it worked
How to check before buying
- Open the installation manual and find its NMEA 2000 PGN list: is the data listed as sent (transmit) on one device and received on the other?
- Read the latest firmware or software release notes; makers often add data in updates.
- Ask your dealer or the maker's support to confirm it with your exact models.
“Tell us if it worked” opens your email app. Reports tell us what to look into; we only mark something compatible when a maker's own document says so.
Gaps and fixes
Data that both devices in a pair handle, but that one can use and the other doesn't send (or sends as a different message number). Fixes only name devices whose published list sends that data.
- Engine & propulsion: different message numbers for Victron Cerbo GX + Garmin GPSMAP x3 (7x3–16x3). Could come from: Maretron J2K100; Yacht Devices YDES-04.
No published data list found yet for: Garmin GHC 50 autopilot helm control, Garmin gWind wind transducer and Garmin Steadycast heading sensor. These are shown as unknown in the checker.
Also in the checker: Victron VE.Bus inverter/charger, Victron Lynx Shunt VE.Can, Victron Lynx Ion BMS, Garmin GPSMAP 8400/8600/8700, Garmin GPSMAP 10x2/12x2, Garmin GPSMAP 7400/7600, Garmin ECHOMAP UHD2 sv, Garmin ECHOMAP UHD, Garmin GPS 24xd, Garmin GND 10, Garmin Reactor 40 CCU, Garmin VHF 315, Garmin AIS 800, Garmin GHC 20, Garmin GHP 12 CCU.
Installing these together
Both connect to one NMEA 2000 backbone. Full basics, with sources, are in the NMEA 2000 install guide.
What you need
- A backbone with one T-connector per device, plus one for the power cable. (Garmin support)
- Drop cables of 6 m (20 ft) or less from each T to its device. (Garmin N2K reference, B&G Zeus S manual)
- Exactly two terminators, one at each end. Don't add more if the boat's backbone already has them. (Garmin N2K reference)
- One fused 12 V power tap, switched so it doesn't drain the battery. (Garmin N2K reference, B&G Zeus S manual, Raymarine docs)
- Victron: Connect the GX device with Victron's VE.Can to NMEA 2000 micro-C male cable. Use the NMEA 2000 cable as the backbone and don't terminate the VE.Can ports into it. (Victron GX manual, Victron guide)
- Victron: Don't join the two networks' power: VE.Can runs at battery voltage (up to 70 V). Remove the cable's fuse when separation is needed. Victron recommends a galvanically isolated port (e.g. Cerbo GX MK2 VE.Can 1). (Victron guide)
- Garmin: Garmin uses standard NMEA 2000 micro connectors. A backbone with mini connectors needs an adapter. (Garmin N2K reference)
- Garmin: The Garmin NMEA 2000 power cable has a 3 A fuse and goes on the top (middle) port of a T-connector, switched so it doesn't drain the battery. (Garmin N2K reference)
Set-up on the display
- Victron: Enable NMEA 2000-out on the GX device. Garmin, Furuno and Navico need no instance setup; Raymarine usually needs unique Battery and DC data instances first. (Victron GX manual, Victron guide)
- Garmin: Check what the plotter sees: Options (or Settings) > Communications > NMEA 2000 Setup > Device List. (Garmin support)
- Garmin: Update the plotter's software (ActiveCaptain app or Garmin Express) when you add a device. (Garmin manual)
- Update each device's software. Garmin says an update may be needed when you add a device or accessory. (Garmin manual, Raymarine docs)
How long? Estimate
No maker publishes a DIY time. Our rough estimate: 1.5–3 hours to add one device to an existing, healthy backbone, or 4–7 hours to build a new small backbone for 2–4 devices.
How we got it: plan the backbone and measure (Garmin says to start with a diagram), run one drop cable, fit Ts, terminators and the power tap, update software, then select sources and test, plus VE.Can cable and GX settings. It doesn't include mounting displays or transducers, cutting holes or long cable runs through the boat. If in doubt, use a qualified (NMEA-certified) installer. (Garmin N2K reference)
Common problems
Only from makers' manuals, support articles and installation guides.
- Batteries show up in the wrong place. Several batteries need different data instances, especially on Raymarine displays. Victron sends the system battery with instance 239. (Victron guide, Victron GX manual)
- Wrong number of terminators. There must be exactly two 120 Ω terminators, one at each end of the backbone. With the network power off, CAN-H to CAN-L should read about 60 Ω. 120 Ω means one is missing; 40 Ω means there's one too many. (Garmin support, Actisense)
- Low network voltage. Devices need at least 9 V at the far end of the backbone (Navico says errors can start below 9.5 V). On long or busy backbones, move the power tap towards the middle. (Actisense, Simrad NSS 4 manual, Garmin N2K reference)
- Duplicate data sources. Two GPS units or two depth sensors on one network can conflict. Pick the preferred source on the display. Raymarine says to have only one source per data type unless a product's documents allow more. (Raymarine 81300, Raymarine LightHouse 4, B&G NEON notes)
- Maker-only features don't cross brands. Standard data flows, but a Garmin plotter can't engage or control a third-party autopilot: it only sends Go To / Route To navigation data. Raymarine Evolution pilots list only Raymarine controllers and displays as control heads. (Garmin support, Raymarine 87472)
More checks (power feeds, devices not showing up): install guide. Check with the manufacturer or a qualified installer before buying or drilling.
What you'll need to connect this
Example: a Victron Cerbo GX and a Garmin GPSMAP x3 (7x3–16x3) on a new backbone.
For 2 devices on one NMEA 2000 backbone. From the makers' install guides; see the install guide for sources. Quantities are estimates
- 1 runBackbone cableLong enough to pass every device; the length depends on your boat. Plan it on a sketch first.
- 3est.T-connectorsOne per device, plus one for the power cable.
- 2est.Drop cablesOne per device, 6 m (20 ft) or less each. Many devices come with a T-connector and drop cable in the box (Garmin lists them for the GPS 24xd, AIS 800 and GND 10), so check before you buy.
- 2TerminatorsExactly two, one at each end. Skip them if your backbone already has two.
- 1Power cable (power tap)One fused 12 V feed, in one place only, switched so it doesn't drain the battery.
One kit covers the basics
Brand adapters for your devices
Check with the manufacturer before buying. Buttons open the maker's own product page unless marked as an affiliate link.
Open these devices in the checker to add the rest of your boat and get a kit list for all of it.
Frequently asked
Are Victron and Garmin compatible?
Yes, mostly one way. We compared 6 Victron–Garmin model pairs using only the data lists (PGNs) the makers publish. 1 has data flowing both ways, 5 one way only. Victron to Garmin: mainly batteries & DC power, tank levels, AC power & generator and switching, lighting & trim. Garmin to Victron: mainly position & time, batteries & DC power and tank levels. Less certain for Victron Cerbo GX, Victron Skylla-i, Victron BlueSolar MPPT 150/70 and Victron BMV-700, because of caveats in their published list (partial list, no send/receive direction, or an older, range-wide or dealer-hosted document). Maker-specific (proprietary) messages, used for things like cross-brand autopilot control or sonar sharing, are not counted between different brands. Check with the manufacturer before buying.
What data can a Victron Cerbo GX and a Garmin GPSMAP x3 (7x3–16x3) share?
From the Victron Cerbo GX to the Garmin GPSMAP x3 (7x3–16x3): batteries & DC power and tank levels. From the Garmin GPSMAP x3 (7x3–16x3) to the Victron Cerbo GX: position & time, batteries & DC power and tank levels. Based on the makers' published PGN lists.
What doesn't work between Victron and Garmin?
For engine & propulsion, some Victron and Garmin models on this page list different message numbers (PGNs), so that data may not show up. The fixes on this page only name devices whose published list sends that data.
Sources
- Victron Cerbo GX (Victron Energy Cerbo GX (and other GX devices) – NMEA2000-out): Cerbo GX Manual, Rev 40 – 04/2026. manufacturer. Last checked 2026-11-19. Confidence: medium; list partial.
- Garmin GPSMAP x3 (7x3–16x3) (Garmin GPSMAP 7x3/9x3/12x3/15x3/16x3 series): GPSMAP Owner's Manual 16x3, 15x3, 12x3, 9x3, 7x3 – NMEA 2000 PGN Information, v16, September 2026. manufacturer. Last checked 2026-11-19. Confidence: high; list complete.
- Victron Skylla-i (Victron Energy Skylla-i / Skylla-IP44 battery charger): Data communication with Victron Energy products (whitepaper), Rev 13, 2013-08-13 (document history). manufacturer. Last checked 2026-11-19. Confidence: medium; list partial.
- Victron BlueSolar MPPT 150/70 (Victron Energy BlueSolar MPPT 150/70 and 150/85 (VE.Can)): Data communication with Victron Energy products (whitepaper), Rev 13, 2013-08-13 (document history). manufacturer. Last checked 2026-11-19. Confidence: medium; list partial.
- Garmin GNX 20/21 (Garmin GNX 20 / GNX 21): GNX 20/21 Installation Instructions, GUID-E313CF8B v8, January 2025. manufacturer. Last checked 2026-11-19. Confidence: high; list complete.
- Garmin GMI 20 (Garmin GMI 20): GMI 20 Installation Instructions, GUID-D193C1DF v6, March 2025. manufacturer. Last checked 2026-11-19. Confidence: high; list complete.
- Victron BMV-700 (Victron Energy BMV-60xS / BMV-700 battery monitor via VE.Direct to NMEA2000 interface): Data communication with Victron Energy products (whitepaper), Rev 13, 2013-08-13 (document history). manufacturer. Last checked 2026-11-19. Confidence: medium; list partial.
Installation sources
- Garmin Support: NMEA 2000 Troubleshooting on Garmin Marine Devices. Checked 2026-11-19.
- Garmin: Technical Reference for Garmin NMEA 2000 Products. Checked 2026-11-19.
- Navico Group (B&G): B&G Zeus S Installation Manual 988-12624-001 – NMEA 2000 planning. Checked 2026-11-19.
- Raymarine: SeaTalk NG cables and accessories. Checked 2026-11-19.
- Victron Energy: Cerbo GX manual – Marine MFD integration by NMEA 2000. Checked 2026-11-19.
- Victron Energy: Marine Integration Guide – NMEA 2000 details (instances, terminators, voltage, isolation). Checked 2026-11-19.
- Garmin: GPSMAP x3 Owner's Manual – Software Updates. Checked 2026-11-19.
- Raymarine: Software updates (product installation instructions). Checked 2026-11-19.
- Actisense: How to build & troubleshoot an NMEA 2000 network. Checked 2026-11-19.
- Navico Group (Simrad): Simrad NSS 4 Installation Manual – NMEA 2000 planning (distributor-hosted copy). Checked 2026-11-19.
- Garmin: Technical Reference for Garmin NMEA 2000 Products – Power Distribution and Balance. Checked 2026-11-19.
- Raymarine: SeaTalk NG Reference Manual 81300 (dealer-hosted copy). Checked 2026-11-19.
- Raymarine: LightHouse 4 – Data sources settings menu. Checked 2026-11-19.
- Navico Group (B&G): NEON 2.5 software release notes (B&G Zeus S / SR). Checked 2026-11-19.
- Garmin Support: Using Third-Party Marine Autopilots with a Garmin Chartplotter. Checked 2026-11-19.
- Raymarine: Evolution EV-1 Autopilot Installation Instructions 87472 Rev 2 (12-2025), ch. 3–4. Checked 2026-11-19.
How we pick pages: chosen by hand from common brand combinations, not from search data. Model pairs are picked automatically from the devices in our dataset (main chartplotter of each brand plus devices that exchange data with it).
Other brand pairs
Garmin + Raymarine · Simrad + Garmin · Lowrance + Garmin · B&G + Garmin · Furuno + Garmin · Humminbird + Garmin · Raymarine + Victron · Victron + Simrad · Victron + B&G · Yacht Devices + Garmin · Actisense + Garmin · Maretron + Garmin · All brand pairs